Dental Lab Quality Control Checklist

Posted by Elemental Dental Supply on Nov 13th 2026

By Elemental Dental Supply | November 2026 | Lab Operations

Every restoration that leaves your lab is your signature. A consistent quality control (QC) process is what separates labs that get call-backs from labs that get referrals. This checklist covers the four critical inspection categories: margin accuracy, shade verification, occlusal clearance, and final review before dispatch.

This isn't a list of suggestions — it's a step-by-step inspection protocol you can print, laminate, and place at your final QC station.

Why a Formalized QC Process Matters

Many lab techs do QC informally — they've done it for years and know what to look for. The problem is that informal QC is person-dependent and inconsistency shows up exactly when you're busy, understaffed, or rushing a case to make a ship date. A written checklist makes QC repeatable regardless of who's at the bench.

It also gives you documentation. When a clinician calls about a case, you can pull the checklist record and know exactly what was verified and by whom. That protects you and gives you a starting point for the conversation.

Stage 1: Margin Inspection

Margins are the most clinically critical aspect of a fixed restoration. Marginal gaps allow microleakage, secondary caries, and cement washout. Open margins are also the number-one reason for remakes.

Tools Required

  • Magnification loupe (minimum 2.5×; 3.5× or 4.5× preferred) or stereomicroscope
  • Illuminated work surface or focused task light
  • Explorer or margin probe

Margin Checklist

  • ✓ Restoration seats fully onto the die — no rocking or resistance
  • ✓ Margin is continuous around the entire preparation — no voids, chips, or open areas
  • ✓ Marginal gap is clinically acceptable (target ≤ 60 µm for cemented restorations; verify with explorer — slight resistance is acceptable, no visible gap)
  • ✓ Internal fit is verified — if using a pressure-indicating paste or silicone fit checker, no high spots at line angles
  • ✓ No over-extension — margin follows the die finish line and does not blanket soft tissue anatomy
  • ✓ Axial walls do not bind against preparation walls (use a light source to check for flash illumination around the margin gap)

Stage 2: Contact Points

Proximal contacts that are too tight cause post-seating pain and gingival trauma. Contacts that are too light allow food packing. Both generate complaints.

  • ✓ Mesial and distal contacts verified on articulated model using shimstock (8 µm foil) — should hold with light resistance and release with firm tug
  • ✓ Contact location is in the middle to occlusal third of the proximal surface — not at the gingival third
  • ✓ No open contacts — shimstock should not pass freely through either proximal
  • ✓ On multi-unit cases, verify each contact individually, not just the spans

Stage 3: Occlusal Clearance and Contacts

Occlusal issues are the most frequent source of chair time at delivery. Verify thoroughly before dispatch.

Centric Occlusion

  • ✓ Restoration is in occlusion on articulator — not in super-occlusion (use articulating paper or shimstock)
  • ✓ Contacts are distributed appropriately — posterior crowns should have broad centric stops, not knife-edge contacts
  • ✓ No single heavy contact point that the clinician will need to adjust at chair

Excursive Movements

  • ✓ Lateral excursion: verify that the restoration does not create a working-side interference that wasn't present on the pre-op model
  • ✓ Protrusive movement: anterior guidance clear of posterior restoration (for posterior cases)
  • ✓ If the case specifies canine guidance or group function, verify the design matches the prescription

Occlusal Surface Anatomy

  • ✓ Cusp height and fossa depth are appropriate — not over-contoured
  • ✓ Ridge anatomy present for full-contour restorations — flat occlusal surfaces without anatomy increase load concentration
  • ✓ For anterior restorations: incisal edge length matches the prescription and contralateral tooth where applicable

Stage 4: Shade and Esthetics

Shade Verification

  • ✓ Compare restoration to shade tab under standard office lighting (D65 or daylight-equivalent bulb)
  • ✓ Check shade in three zones: cervical (typically darker), body (base shade), incisal (typically lighter/translucent)
  • ✓ Value (brightness) matches before checking hue — the most common shade mismatch is value, not hue
  • ✓ For layered restorations, verify under different light sources (daylight, incandescent, and fluorescent) to check for metamerism
  • ✓ Translucency appropriate for the age of the patient and adjacent teeth

Surface Finish

  • ✓ Glaze or polish is smooth and even — no rough patches, overglazing streaks, or dry spots
  • ✓ No characterization stain applied outside the prescription request
  • ✓ Surface texture matches the adjacent dentition where visible (anterior cases)

Stage 5: Final Pre-Dispatch Checklist

ItemPassNotes
Tooth number correct per Rx☐
Material matches Rx☐
Shade matches Rx☐
Case is clean — no gypsum, wax, or polish residue☐
No visible cracks or chips (under magnification)☐
Implant cases: correct connection size per Rx☐
Return model included (if required)☐
Pan photos taken (if required by lab SOP)☐
Cementation instructions included for unusual materials☐
QC tech initials recorded☐

Building QC Into Your Lab Culture

QC is not just a final checkpoint — it's a feedback loop. When you catch a marginal gap at final QC, that's a sign of an upstream problem (scanner calibration, milling wear, design parameter). Track your QC failures by category for 60 days and you'll identify where your process needs attention. Most labs find that 80% of QC failures come from 2–3 recurring sources once they start tracking.

Assign QC to someone other than the person who built the case when possible. Self-QC works, but a second set of eyes catches what familiarity blinds.

Finally, make QC the last step before packing, not something done at the bench while the next case is being started. The environment matters — good lighting, clean surface, and no distractions are not optional for a final inspection.

Elemental Dental Supply — dental lab equipment and supplies in Tempe, AZ. elementaldentalsupply.com | 866-901-8443