A facebow record is one of the few pieces of patient information that cannot be recreated at the bench. If it arrives distorted, incomplete or in a format the lab’s articulator cannot accept, the case is mounted on guesswork, and the occlusion the technician builds will be adjusted chairside or remade.
This guide is written for lab owners and technicians who want to tighten the handoff: what a good facebow transfer includes, what goes wrong, and a checklist you can share with your clinics.
What a Facebow Transfer Records
A facebow captures the position of the maxillary teeth relative to two things: the hinge axis of the jaw and a horizontal reference plane. Most clinics use an earbow-style facebow that locates an average (arbitrary) hinge axis from the ear rods and uses a third reference point, such as a nasion relator or orbital pointer, to set the plane. Kinematic facebows that locate the true hinge axis exist but are uncommon in everyday cases.
The record itself is the bite fork: a fork loaded with registration material, seated against the maxillary teeth and locked to the bow. In the lab, the fork and its orientation are used to mount the maxillary cast. Everything after that, including the mandibular mounting and any condylar programming, builds on that first step.
What the Lab Needs to Receive
The fork record, intact
The lab needs the bite fork with its registration material undamaged, plus either the complete facebow or the transfer component designed for its system. Many systems use a transfer jig or transfer base so the clinic keeps the bow and sends only the fork assembly; Whip Mix QMS transfer bases and Denar Slidematic jigs are examples. Confirm in advance which system each clinic uses and whether your articulators accept it.
Jaw relation records
For the mandibular cast, the lab needs an interocclusal record taken at the position the dentist wants the restoration built to, whether that is centric relation or maximum intercuspation, with a note saying which. If the articulator will be programmed, protrusive and lateral records are needed too.
Accurate casts or scans
Casts must seat fully in the fork indentations. Bubbles or nodules on occlusal surfaces stop that from happening, and so does an impression that is distorted.
Written intent
Tell the lab whether vertical dimension is changing, by how much and which record reflects it. A photo of the patient with the facebow in place is very helpful: it lets the technician check whether the bow was level with the face and whether the occlusal plane looks right.
Common Errors That Distort the Mounting
- Fork record rocks or perforates. If teeth punch through the registration material to the metal, or the record rocks on the cast, the orientation is unreliable. Thin, stable records that capture only cusp tips seat best.
- Joints slip in transit. A toggle or clamp not fully tightened, or a bow knocked in the box, changes the record before it reaches the lab. Pack the fork assembly so nothing bears on the joints.
- Distorted registration material. Wax records can soften and warp in a hot vehicle or mailbox. Rigid elastomeric bite materials hold up better in shipping; follow the material IFU.
- Ear rods not seated or bow not level. A canted bow transfers a canted occlusal plane. The lab cannot correct this without a reference photo.
- System mismatch. A fork from one facebow system mounted on an incompatible articulator with an improvised support is a common source of error.
- Records for the wrong position. Receiving a centric relation record with no note, then building to MIP, or the reverse, shows up as a high restoration.
Receiving the Transfer in the Lab
Mounting technique depends on the articulator, so follow its instructions. The facebow-specific checks come first, before any plaster is mixed:
- Inspect the fork: check that joints are tight, the record is intact and nothing has been bent.
- Disinfect or handle the record according to your lab’s infection-control protocol.
- Confirm the fork or transfer component belongs to a system your articulator accepts. If it does not, call the clinic before improvising.
- Trial-seat the maxillary cast in the fork indentations. It should seat without rocking. If it rocks, find out why before mounting.
- Support the fork so the cast’s weight cannot move it while the mounting material sets. A fork support such as the Whip Mix QuickMount facebow fork support exists for exactly this.
- Mount with a low-expansion material such as Whip Mix Mounting Plaster, then verify the mandibular mounting against the clinic’s notes and photos before you start work.
A Communication Checklist to Share with Clinics
- Facebow system and model, and whether a transfer jig or base is being sent instead of the full bow.
- Bite fork record intact, stable and not perforated, with joints tightened before packing.
- Which position the jaw relation record represents (CR or MIP) and whether vertical dimension changes.
- Protrusive and lateral records if the dentist wants the articulator programmed.
- A front-facing photo with the facebow in place, plus a smile photo for anterior cases.
- Any condylar values the clinic has already measured.
- Impressions or casts free of occlusal bubbles, and disinfected per the clinic’s protocol.
Keep a stock of bite forks so clinics are never tempted to skip the record because forks have not come back. Whip Mix forks EDS lists include the #8610 curved-stem dentulous fork and the #8632 edentulous fork.
Where Facebow Records Matter Most
Full-arch and immediate-load implant cases are where a poor transfer costs the most, because they change vertical dimension, occlusal plane and anterior guidance all at once. If your lab handles them, our guide to immediate-load implant restorations covers the other records worth asking for, and our exocad occlusion tips explain how a mounted relationship carries into digital design.