Full-Arch Digital Implant Workflow: Scanner to Delivery

Posted by Elemental Dental Supply on Nov 17th 2026

By Elemental Dental Supply | November 2026 | Implant Lab Work

Full-arch implant cases are among the most demanding work that flows through a dental lab. When something goes wrong — a passivity failure, a wrong connection size, an occlusal discrepancy — it's expensive, time-consuming, and hard on the patient relationship. A documented, repeatable workflow protects against those failures. This guide covers the full-arch digital process from scan intake to final delivery, with attention to the decision points where most errors originate.

Step 1: Scan File Intake and Verification

Before you design anything, verify the incoming data. This is the most commonly skipped step and the most frequently regretted one.

  • Scan body identification: Confirm which scan bodies are in the file. If the clinician used ELOS Easy, Straumann CARES, or any other proprietary scan body, your CAD library must have the matching virtual analog. Mismatched scan bodies mean wrong implant positions — every subsequent step will be wrong.
  • Connection verification: Cross-reference the Rx with the implant chart or implant record. Confirm: implant brand, connection type (internal hex, conical, etc.), diameter, and ti-base or abutment platform specification.
  • Scan quality check: Open the scan in your CAD software. Look for scan gaps at the fixture level — the area around each scan body must be clean. Gaps here create incorrect virtual implant positioning. Flag and return if any scan body is obstructed or partially obscured.
  • Opposing arch and bite registration: Full-arch cases require an opposing arch scan and a bite scan (centric or protrusive). Confirm both are present and that the bite registration registers cleanly. A bite that doesn't seat in the software is a rescan request.

Step 2: Virtual Model and Implant Positioning

Once scan data is verified, build the virtual model:

  1. Import scan files into your CAD software (exocad, 3Shape Dental Designer, etc.)
  2. Place virtual implant analogs at each scan body position — verify each one individually. The software usually auto-detects based on the library; manually confirm position and angulation before proceeding.
  3. Set occlusal plane reference from the opposing arch scan
  4. Confirm midline, smile line (if esthetic case), and vertical dimension from the bite registration or provided setup

Step 3: Design Phase

Full-arch design is significantly more complex than single-unit work. Key design decisions:

Framework vs. Monolithic

Most full-arch cases today use either a milled titanium or zirconia framework with veneering, or a monolithic zirconia arch with no separate framework. Each has implications:

  • Monolithic zirconia full arch: Single-material, fast production, no delamination risk. Requires the right zirconia grade (4Y or 5Y multi-layered for esthetics). Minimum connector cross-section of 12 mm² is critical — below this, connector fracture is a real risk.
  • Titanium framework + veneering: Superior passivity, easier to repair, can veneer with composite or ceramic. More complex workflow and longer production time.

Connector and Pontic Design Rules

  • Minimum connector cross-section: 12 mm² for zirconia, 7 mm² for titanium
  • Pontic tissue contact: egg-shaped ovate or modified ridge lap — do not design pressure-bearing tissue contact
  • Screw access channel: positioned lingual or occlusal depending on implant angulation. For angled access, use a dedicated angled screw channel design (exocad has a specific module for this).

Screw Channel Verification

Before finalizing design, run a visual check on all screw channels. Each channel must:

  • Clear the restoration walls without intersecting a connector
  • Emerge at an accessible location (lingual or occlusal, not through a cusp tip)
  • For angled channels: verify the angulation correction component (e.g., Multi-unit abutment or angled ti-base) is in the design

Step 4: Milling the Full-Arch Restoration

Full-arch milling requires a mill that can handle large workpieces — most desktop 5-axis mills can handle up to 98 mm pucks, which is the standard for full-arch cases.

  • Use fresh burs — full-arch milling puts significant mileage on burs, and worn burs cause surface roughness and potential connector finish issues
  • For zirconia full arch, milling time is typically 45–90 minutes depending on the mill and material
  • Inspect the green-state arch carefully before sintering: check connector geometry, margin integrity at each fixture, and screw channel clearance
  • Do not attempt to adjust the green-state arch with a bur — the structure is fragile and any contact risks fracture. Remake if there are significant issues.

Step 5: Sintering Full-Arch Zirconia

Sintering a full-arch is more demanding than a single unit. Support is critical:

  • Use the sintering bead bed — the arch must be supported at multiple points along its length to prevent sagging during the high-temperature dwell
  • Orient the arch so the occlusal surfaces are accessible (typically arch inverted or on its side, supported at the connectors)
  • Do not stack or allow the arch to contact furnace elements
  • For large arches (>14 units), verify your sintering furnace has adequate chamber volume and temperature uniformity. Hot spots cause differential shrinkage and passivity failure.

Step 6: Post-Sinter Verification — The Passivity Test

Passivity of fit is the single most important criterion for a full-arch implant prosthesis. A non-passive prosthesis creates unresolved stress at each implant — and implant failure or bone loss follows.

Test passivity using the single-screw test on the analog model:

  1. Place the prosthesis on the model without any screws
  2. Tighten one screw (usually the most distal) to the specified torque
  3. Check all other fixture interfaces with a probe or explorer — there should be no visible gap or movement
  4. Repeat by tightening each screw individually while checking the others

If any gap is visible, the prosthesis does not pass. For zirconia full arches, discrepancy must be addressed — either remill or use a sectioning and bonding protocol to correct the fit before delivery.

Step 7: Finishing and Dispatch

  • Polish the prosthesis (see polishing protocol for monolithic zirconia)
  • Verify occlusion on articulated model — centric contacts, lateral excursion, protrusive guidance
  • Verify screw channel access with the appropriate driver
  • Package with: the prosthesis, spare screws (if provided), connection specifications, torque values, and a passivity test report if your lab documents these
  • Include instructions for screw access channel sealing material (PTFE tape + composite or silicone plug)

Common Points of Failure — Quick Reference

Failure ModeRoot CausePrevention
Wrong connection at deliveryScan body mismatch or Rx not verifiedStep 1 verification; cross-check Rx
Passivity failureScan gap at fixture, sinter support errorScan QC at intake; proper sinter support
Connector fractureUnder-dimensioned connector designMinimum 12 mm² cross-section rule
Occlusal discrepancyBite registration errorVerify bite registration seats cleanly before design
Screw channel inaccessibleNot verified in designScrew channel simulation in CAD before milling

Full-arch digital workflows have matured significantly — the tools are reliable when used correctly. The discipline is in the intake verification and the passivity test. Getting those right makes the rest of the workflow straightforward.

Elemental Dental Supply — dental lab equipment and supplies in Tempe, AZ. elementaldentalsupply.com | 866-901-8443