The debate between pressed and milled glass ceramics is not new, but it deserves a technical framing rather than a brand loyalty discussion. Both methods produce lithium disilicate (or related glass ceramic) restorations. The differences come down to how the crystallization occurs, what types of cases each handles best, and what the true workflow cost is for your lab. This guide covers both sides honestly.
Understanding the Material State Difference
The key to understanding the pressing vs. milling debate is the crystallization stage at which you're working with the material:
Pressing (Heat-Press Method)
Wax-up is invested and pressed using a pre-crystallized ingot (e.g., IPS e.max Press). The ingot is heated until viscous (~915°C for e.max LT) and forced into the investment mold under pressure. The pressed restoration is in a partially crystallized state, which allows easy adjustment and finishing. A final crystallization/glaze firing completes the microstructure and achieves full strength (~400 MPa for e.max).
Milling (CAD/CAM Method)
Milling works from either a pre-crystallized block (e.g., IPS e.max CAD — blue/soft state) or a fully crystallized block (less common). The pre-crystallized block is machined in the soft state (easy on burs, faster milling), then fired in a crystallization furnace to achieve final dimensions and full strength. Some labs mill fully crystallized blocks, which requires a more aggressive milling strategy but eliminates the firing step.
Mechanical Properties: Are They Actually Different?
Both processes can achieve similar peak flexural strength when properly executed. The e.max system in both press and CAD versions targets ~400 MPa post-crystallization. The practical differences are:
- Consistency: Pressed restorations have more process variables (wax-up quality, investment ratio, pressing temperature, burnout). CAD/CAM has tighter dimensional control but depends on block quality and bur wear.
- Microstructure: Pressed glass ceramics often have slightly more homogeneous crystal distribution because the material flows and crystallizes uniformly. Milled blocks can have tool marks that, if not removed, act as stress risers.
- Veneers and thin margins: Pressing has an edge for very thin margins (<0.3 mm) because the material flows into the investment cavity without the geometric constraints of a bur path. Milled margins at this thinness risk chipping during machining.
Workflow Comparison
| Step | Pressing | Milling (CAD/CAM) |
|---|---|---|
| Preparation | Wax-up, invest, burnout | Scan, CAD design |
| Primary processing | Press (25–30 min per cycle) | Mill (12–25 min per unit) |
| Post-process | Divest, adjust, stain/glaze fire | Crystallization fire, stain/glaze |
| Total time (single unit) | 3–5 hours (including investment time) | 1.5–3 hours |
| Batching efficiency | Excellent — press multiple units simultaneously | Moderate — one or two units per milling cycle |
| Remake cost | Low material cost; high time cost | Higher material cost (block); lower time cost |
| Capital equipment | Press furnace ($8K–15K) | Mill ($20K–$80K) + crystallization furnace |
When Pressing Wins
Veneers and Thin Restorations
Pressing is the preferred method for ceramic veneers, especially ultra-thin preparations (0.3–0.5 mm). The ability to flow material into thin wax-up forms gives you precise control over thickness distribution that milling cannot match at this scale. Milling 0.3 mm facial veneers is technically possible but requires exceptional bur condition and produces a non-trivial chipping rate at the margins.
Complex Anatomical Forms
Pressing follows the wax-up exactly. If your technicians produce excellent hand-wax anatomy, pressing preserves that fidelity. For highly characterized or anatomically complex cases where wax carving skill is the variable, pressing lets that skill translate directly to the final restoration.
High-Volume Single-Material Labs
If your lab does primarily pressed e.max with a skilled pressing team, batching is very efficient. You can press 4–6 units per cycle with a 30-minute press time. A small pressing lab without a mill can be very productive on the right case mix.
Bridgework (Short Span)
Three-unit anterior bridges in e.max Press are well-documented clinically. Pressing allows proper connector wax-up and uniform material distribution through the connector. Milled connectors are mechanically equivalent but require attention to connector cross-section in the CAD design.
When Milling Wins
Single-Unit Crowns (Posterior)
For posterior single-unit crowns where speed matters and a fully milled monolithic result is acceptable, milling is faster per unit and requires no investment materials or burnout furnace. Most full-service digital labs default to milling for posterior glass ceramic cases for this reason.
Consistency in High Volume
CAD/CAM produces the same geometry every time, regardless of technician variability. For labs processing 20+ glass ceramic units per day, milling provides more consistent marginal accuracy than press (which depends on investment expansion, pressing temperature, and wax-up precision for each unit).
Same-Day Workflows
In-office milling or labs supporting chairside dentistry need short turnaround times. Milling a pre-crystallized block and firing takes ~90 minutes start to finish. Pressing requires wax-up time, investment, burnout, pressing, and divesting before finishing — same-day turnaround is possible but tight.
Reduced Investment Consumable Cost
Pressing requires investment material, sprue wax, casting rings, and ring liner for every case. Milling requires only the block and burs. For labs managing consumable costs carefully, milling has lower per-unit material cost once the equipment is amortized.
Hybrid Approach: What Most Labs Do
Many labs don't choose one method exclusively — they press for veneers and use specific pressed cases (complex anatomical, very thin), and mill for crowns, inlays, and high-volume work. This hybrid approach captures the advantages of each method at the cost of maintaining both workflows and equipment.
If your lab has both capabilities, the decision rule is simple: press when the wax-up advantage is meaningful (thin, complex, or esthetic anterior cases); mill when speed, consistency, or per-unit economics are the primary factors.
Equipment Considerations
Starting a pressing program requires a heat press furnace (IPS e.max Press uses the Programat EP series or Ivoclar P700). Starting a CAD/CAM program requires significantly higher capital — a 5-axis mill plus a crystallization furnace. For labs without digital infrastructure, pressing can be the economical path to glass ceramic production. For labs already running a digital workflow, adding pressing for veneers and anterior cases extends the range of cases without requiring a separate scan-and-design step.