The cheapest time to fix a zirconia restoration is before it goes into the furnace. Pre-sintered zirconia cuts easily, grinding damage is not a concern, and detail work that would take minutes with diamonds after sintering takes seconds. The trade-off is fragility: the same restoration that will be extremely strong after sintering can be broken with careless fingers beforehand.
This guide covers finishing in that window: separating from the disc, contouring, smoothing, cleaning before sintering and the habits that lead to cracks or discoloration.
What “Green State” Means Here
Strictly speaking, milled zirconia discs are pre-sintered (sometimes called the white or bisque state). The material has been partly fired so it holds its shape and can be milled, but it is still porous, chalky and much weaker than the final restoration. Most labs call this the green state, and so will this article.
Two properties of pre-sintered zirconia shape everything below:
- It is milled oversize. Restorations shrink substantially during sintering, so the CAM software scales them up using a factor specific to the disc. Any adjustment you make shrinks with the restoration, and a small dip or flat spot left now will still be there after sintering.
- It is porous. It absorbs liquids, oils and fine debris readily, which affects coloring-liquid uptake and can leave marks after sintering.
Handling Pre-Sintered Restorations
- Work with clean, dry hands or gloves. Skin oils and lotions can block coloring liquid and show up as blotches.
- Support the restoration across its whole body, especially bridges. Do not hold a bridge by one retainer or pinch it at the margins.
- Work over a soft surface so a dropped unit does not crack.
- Use instruments reserved for zirconia. Cutters or diamonds that have been used on metal can leave particles in the porous surface, which may show up as dark spots after sintering.
Separating Sprues and Connectors
The restoration is still held in the disc by its sprue connectors. Removing them cleanly is the most common green-state task, and the most common source of chipped margins.
- Cut with a thin diamond disc or a dedicated green-state instrument at low speed with no pressure. Let the instrument work through the connector rather than snapping the restoration out.
- Cut partly through from more than one side on thicker connectors, so the last bit of material does not break away and take part of the restoration with it.
- Leave a small stub rather than cutting flush against the restoration, then blend it into the contour with a fine instrument.
- Keep connector sites away from margins where possible at the CAM stage, so separation never happens right at a thin edge.
Wagner’s Green State Contour system is designed for removing sprue connectors and contouring pre-sintered zirconia before sintering.
Contouring and Smoothing
With the restoration free, use the green state to do the work you would otherwise do with diamonds on sintered material:
- Remove milling steps and tool marks on axial walls and occlusal surfaces with a fine instrument and light strokes.
- Refine anatomy. Deepen fissures where the milling tool could not reach, sharpen marginal ridges and soften overly sharp cusp tips. Wagner’s ZHP Diamonds are designed for anatomical adjustments on green-state restorations.
- Check contacts and occlusion on the model now, allowing for shrinkage, because both are far easier to correct before sintering.
- Open embrasures carefully on bridges, but never thin the connectors below the cross-section designed in CAD. Connector size is set for strength, and the gingival embrasure is where fractures start.
- Treat margins gently. Thin margins chip easily in the green state. Blend from the restoration toward the margin and stop short of the edge.
Green-State Polishing
Smoothing the surface before sintering means less polishing afterwards, and a smoother pre-sintered surface generally comes out of the furnace smoother. Harvest’s Nano Zirconia Green State Polish System is designed for polishing zirconia restorations in the green state. Follow its IFU for sequence and speed. Green-state polishing reduces the work after sintering but does not replace it. Any area you adjust after sintering still needs a full polish.
Cleaning Dust Before Sintering
Loose zirconia dust left on the restoration can sinter onto the surface as bumps, fill fissures or seat on the intaglio and affect fit. Clean every unit before coloring or sintering:
- Brush the restoration with a soft, clean, dry brush, including fissures and the intaglio.
- Use gentle, clean, oil-free air. Shop air from a compressor without good filtration can blow oil and moisture into the porous surface.
- Do not steam-clean or put the restoration in an ultrasonic cleaner unless the zirconia manufacturer allows it.
- If the restoration has been wetted, by coloring liquid or anything else, dry it completely according to the IFU before sintering. Moisture trapped in the pores can cause cracking during heat-up.
If you color your restorations, this is the point to do it. Our zirconia coloring liquids technique guide covers application and drying.
What Not to Do
- Do not apply pressure to “help” an instrument cut. Pre-sintered zirconia needs almost none.
- Do not run green-state instruments at high speed out of habit. Low speed gives control and keeps the instrument from grabbing.
- Do not mark restorations with pencils or markers unless the material manufacturer says it is safe. Residue can affect the sintered color.
- Do not sinter a restoration you have not inspected for cracks. A crack in the green state does not heal in the furnace.
- Do not let zirconia dust build up on the bench. Use local extraction while grinding, wear appropriate respiratory protection and follow the SDS. Collect dust rather than sweeping it into the air.
Once the restoration is clean and dry, the sintering program does the rest. Our article on how sintering temperature profiles affect zirconia explains why following the manufacturer’s program matters.