Type II to Type V Gypsum: Choosing Die Stone for the Lab

Posted by Elemental Dental Supply on Nov 15th 2026

By Elemental Dental Supply | November 2026 | Lab Materials

Digital workflows have taken a lot of models off the bench, but gypsum is far from finished. Conventional impressions still arrive, dentures and partials are still mounted on stone, and every printed model eventually meets a mounting plaster. Choosing the wrong class of gypsum for the job is one of the quieter causes of tight contacts, open margins and remakes.

This guide walks through the gypsum classes a lab actually uses, what separates them, and the handling habits that decide whether a good stone performs like one.

How Dental Gypsum Is Classified

Dental gypsum products are grouped into five types under the ISO standard for dental gypsum (the older ADA specification uses the same numbering, which is why you will see Roman numerals on many bags). Type I is impression plaster and rarely shows up in a lab today. Types II through V are the working materials:

  • Type II, model plaster: the softest and weakest of the working types, fine for jobs where strength and surface detail do not matter much.
  • Type III, dental stone: harder and stronger than plaster, the standard for study models, opposing models and denture work.
  • Type IV, die stone (high strength, low expansion): the default for crown and bridge dies and working models.
  • Type V, die stone (high strength, high expansion): similar strength, but with more setting expansion built in.

The two properties that drive the choice are strength (and the surface hardness that comes with it) and setting expansion. Everything else, including color, set time and flow, is about workflow preference.

Plaster: Boxing, Bases and Mounting

Plaster earns its place where you want something cheap, easy to trim and quick to remove: bases, boxing, flasking support and general bench work. Whip Mix Laboratory Plaster is a general-purpose plaster for model pours, boxing and base mounting.

Mounting is its own category. A mounting material should have minimal setting expansion so it does not shift the cast relationship as it sets, and it should bond well to the mounting plate. Whip Mix Mounting Plaster is made for mounting casts to Hanau, Denar and Whip Mix articulators, and Whip Mix also offers mounting stones for labs that prefer a harder mount.

Type III Stone: Study, Opposing and Denture Models

Type III stone is the everyday model material. It is strong enough to survive articulation and handling, but it does not need the hardness of a die. Typical uses include diagnostic and study models, opposing models, orthodontic casts and complete or partial denture work.

Whip Mix model stones EDS carries include Microstone, Buffstone, Orthodontic Stone and Bitestone. Setting times, colors and ISO types differ from product to product, so confirm the type and working time on the label or IFU before you standardize on one.

Type IV Die Stone: The Crown and Bridge Default

Type IV is where most fixed work lives. High strength and surface hardness let dies survive repeated seating, ditching and margin marking without abrading, and low setting expansion keeps the die close to the impression. For single units, short spans and most implant working models, Type IV is the safe starting point.

Whip Mix Silky-Rock is a low-expansion Type IV die stone known for a smooth surface that helps with margin definition, available in several colors. Whatever brand you use, keep one die stone as your standard so your spacer and fit settings stay calibrated to it.

Low expansion matters most on implant models. When analogs are set in stone, any unwanted expansion moves the analogs relative to each other, and a passive multi-unit framework depends on that relationship. If you are deciding between stone and printed models with digital analogs, our guide to digital versus physical analogs covers the trade-offs.

Type V Die Stone: When You Want More Expansion

Type V stone combines die-stone strength with higher setting expansion. That extra expansion is used to help compensate for the solidification shrinkage of some casting alloys, particularly base-metal alloys, so the casting is not undersized on the die. It is a deliberate choice, not an upgrade: using Type V where your workflow is tuned for Type IV can leave crowns loose.

If your alloy and investment system calls for a Type V stone, confirm the type on the label and the expansion figure in the IFU and match it to your alloy, investment and spacer system.

Mixing Best Practice

A premium die stone mixed carelessly behaves like a cheaper one. The habits below are general; always follow the water-to-powder ratio and mixing time on the manufacturer’s IFU for the specific product.

  • Weigh the powder and measure the water. The water-to-powder ratio has the biggest single effect on strength, hardness and expansion. Extra water makes a weaker, softer die; too little shortens working time and traps air.
  • Use consistent water. Clean, room-temperature water (distilled if your IFU calls for it) gives predictable set times. Warm water and contaminated bowls speed the set.
  • Add powder to water, wet it by hand, then vacuum mix for the time the IFU specifies. Vacuum mixing noticeably reduces porosity in die stone.
  • Keep bowls and spatulas clean. Set gypsum left in a bowl acts as an accelerator for the next mix.

Pouring and Handling

  • Wait the time recommended by the impression material manufacturer before pouring, and make sure the clinic has disinfected the impression to its protocol.
  • A surfactant such as Harvest Surfactant can help stone wet a hydrophobic impression surface.
  • Pour on a vibrator from one side and let the stone flow ahead into each preparation. Moderate vibration helps; aggressive vibration can pull air into the mix. We reviewed a dedicated unit in our Trident Good Vibrations lab vibrator review.
  • Do not separate the impression until the stone has reached the separation time on the IFU. Dry strength keeps rising after that, so give dies time before heavy trimming.
  • Never rinse set dies under plain running water for long. Gypsum is slightly soluble, and fine surface detail suffers. Use slurry water when you need to wet a model.

Storage and Safety

Gypsum absorbs moisture from the air. Damp powder sets unpredictably and produces weaker models, so keep bags and bins sealed, rotate stock first in, first out, and do not top up an old bin with a new lot. Trimming and grinding gypsum makes fine dust: use local extraction at the model trimmer and bench, wear appropriate respiratory protection, and follow each product’s SDS.

Elemental Dental Supply — we carry Whip Mix plasters, model stones and die stones for every step from study model to working die. Shop Whip Mix Silky-Rock or call 866-901-8443.